one source for HYDRAULIC AND PNEUMATIC CYLINDERS

Milwaukee Cylinder Pneumatic Cylinders

MILWAUKEE Series "A" pneumatic cylinders are built to perform on the toughest applications. Incorporating a variety of MILWAUKEE "Exclusive" advanced features, proven through the years, these cylinders will provide a long, maintenance-free service life. Advanced engineering combined with quality materials and expert workmanship contribute to the making of a rugged, top quality pneumatic cylinder.


Series A - Pneumatic Cylinders - Steel

MILWAUKEE Series "A" pneumatic cylinders are built to perform on the toughest applications. Incorporating a variety of MILWAUKEE "Exclusive" advanced features, proven through the years, these cylinders will provide a long, maintenance-free service life. Advanced engineering combined with quality materials and expert workmanship contribute to the making of a rugged, top quality pneumatic cylinder.


Tie Rod Mounts

The flange and tie-rod mounts are basically the same, except that the cylinder tie rods are extended and used to mount the cylinder. To prevent misalignment, sagging or possible binding of the cylinder, the free end should be supported. The best use of tie-rods when extending on the blind end is in a thrust load application. When using tie-rods extended on the rod end, the best application is a tension load. Tie rod mounts are suited for many applications, but it should be noted that they are not as rigid as the flange type of mounting.

Both Ends
Model A10
NFPA MX1
1.5" to 6" Bore
8" to 16" Bore
No Extension
Model A11
NFPA MX
1.5" to 6" Bore
8" to 16" Bore
Rod End
Model A12
NFPA MX3
1.5" to 6" Bore
8" to 16" Bore
Blind End
Model A13
NFPA MX2
1.5" to 6" Bore
8" to 16" Bore

 


Flange Mounts

The flange mount is one of the strongest, most rigid methods of mounting. With this type of mount there is little allowance for misalignment, though when long strokes are required, the free end opposite the mounting should be supported to prevent sagging and possible binding of the cylinder. The best use of a blind end flange is in a thrust load application (rod in compression). Rod end flange mounts are best used in tension applications. If an application exceeds the rectangular flange rating, requiring an extra heavy flange, a solid flange style end cap mount is available at no extra cost for most bore sizes. When a less rigid mount can be used and the cylinder can be attached to a panel or bulkhead, an extended tire rod mounting could be considered.

Rod Square
Model A21
NFPA MF5
1.5" to 6" Bore
NFPA ME3
8" to 16" Bore
Blind Square
Model A22
NFPA MF6
1.5" to 6" Bore
NFPA ME4
8" to 16" Bore
Rod Rectangular
Model A31
NFPA MF1
1.5" to 6" Bore
Blind Rectangular
Model A32
NFPA MF2
1.5" to 6" Bore

 

Side and Lug Mounts

The side or lug mounted cylinder provides a failrly rigid mount. These types of cylinders can tolerate a slight amount of misalignment when the cylinder is at full stroke, but as the piston moves toward the blind end, the tolerance for misalignment decreases. It is important to note that if the cylinder is used properly (without misalignment), the mounting bolts are either in simple shear or tension without any compound stresses.

Tapped Holes
in Caps Flush
Model A41
NFPA MS4
1.5" to 6" Bore
8" to 16" Bore
Side Lug
Model A42
NFPA MS2
1.5" to 6" Bore
8" to 16" Bore
Foot
Model A43
NFPA MS7
1.5" to 6" Bore
8" to 16" Bore
Centerline Lug
Model A51
NFPA MS3
1.5" to 6" Bore
8" to 16" Bore

 
Pin and Trunnion Mounts

All pin and trunnion cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion pivot pins should be carred by bearings that are rigidly held and closely fit for the entire length of the pin.

Clevis
Model A61
NFPA MP1
1.5" to 6" Bore
8" to 16" Bore
Fixed Eye
Model A62
1.5" to 6" Bore
8" to 16" Bore
Rod End Trunnion
Model A71
NFPA MT1
1.5" to 6" Bore
8" to 16" Bore
Blind End Trunnion
Model A72
NFPA MT2
1.5" to 6" Bore
8" to 16" Bore
Center Trunnion
Model A73/A74
NFPA MT4
1.5" to 6" Bore
8" to 16" Bore

 
Double Rod End

Double rod end styles are available in every mounting style except 61 and 62. When specified by the customer, the standard mountings offered by Milwaukee Cylinder may be combined. Combinations such as 31 mounting on one end and a 42 mounting on the other can be readily made from standard parts.

Double Rod End
NFPA MDX
1.5" to 6" Bore
8" to 16" Bore


Series MN - Pneumatic Cylinders - Aluminum

MILWAUKEE Series "MN" pneumatic cylinders are built to perform on the toughest applications. Incorporating a variety of MILWAUKEE "Exclusive" advanced features, proven through the years, these cylinders will provide a long, maintenance-free service life. Advanced engineering combined with quality materials and expert workmanship contribute to the making of a rugged, top quality pneumatic cylinder.



Tie Rod Mount

The flange and tie-rod mounts are basically the same, except that the cylinder tie rods are extended and used to mount the cylinder. To prevent misalignment, sagging or possible binding of the cylinder, the free end should be supported. The best use of tie-rods when extending on the blind end is in a thrust load application. When using tie-rods extended on the rod end, the best application is a tension load. Tie rod mounts are suited for many applications, but it should be noted that they are not as rigid as the flange type of mounting.

Both Ends
Model MN10
NFPA MX1
1.5" to 12" Bore
No Extension
Model MN11
NFPA MX
1.5" to 12" Bore
Rod End
Model MN12
NFPA MX3
1.5" to 12" Bore
Blind End
Model MN13
NFPA MX2
1.5" to 12" Bore

 

Flange Mounts

The flange mount is one of the strongest, most rigid methods of mounting. With this type of mount there is little allowance for misalignment, though when long strokes are required, the free end opposite the mounting should be supported to prevent sagging and possible binding of the cylinder. The best use of a blind end flange is in a thrust load application (rod in compression). Rod end flange mounts are best used in tension applications. If an application exceeds the rectangular flange rating, requiring an extra heavy flange, a solid flange style end cap mount is available at no extra cost for most bore sizes. When a less rigid mount can be used and the cylinder can be attached to a panel or bulkhead, an extended tire rod mounting could be considered.

Rod Square
Model MN21
NFPA ME3
8" to 12" Bore
Blind Square
Model MN22
NFPA ME4
8" to 12" Bore
Rod Rectangular
Model MN31
NFPA MF1
1.5" to 6" Bore
Blind Rectangular
Model MN32
NFPA MF2
1.5" to 6" Bore


Bottom Tap, Lug and Angle Mounts

The side or lug mounted cylinder provides a fairly rigid mount. These types of cylinders can tolerate a slight amount of misalignment when the cylinder is at full stroke, but as the piston moves toward the blind end, the tolerance for misalignment decreases. It is important to note that if the cylinder is used properly (without misalignment), the mounting bolts are either in simple shear or tension without any compound stresses.

Bottom Tap
Model MN41
NFPA MS4
1.5" to 12" Bore
Side Lug
Model MN42
NFPA MS2
1.5" to 8" Bore
Angle
Model MN44
NFPA MS1
1.5" to 8" Bore


Pin Mounts

All clevis cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion pivot pins should be carried by bearings that are rigidly held and closely fit for the entire length of the pin.

Clevis
Model MN61
NFPA MP1
1.5" to 12" Bore
Fied Eye
Model MN62
NFPA MP4
1.5" to 8" Bore
Removable Clevis
Model MN63
NFPA MP2
1.5" to 8" Bore

 

Trunnion Mounts

All trunnion cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion pivot pins should be carried by bearings that are rigidly held and closely fit for the entire length of the pin.

Rod End Trunnion
Model A71
NFPA MT1
1.5" to 8" Bore
Blind End Trunnion
Model A72
NFPA MT2
1.5" to 8" Bore
Center Trunnion
Model A73
NFPA MT4
1.5" to 8" Bore

 

Double Rod End

Double Rod End
NFPA MDX
1.5" to 8" Bore